(еК2.390.419)
The controller contains powerful computing resources in the absence of an operating system: The module is designed for use in control and recording systems, digital signal processing systems with high demands on speed, volume of data processed, reliability and fault tolerance as a computing and control node.
The module receives, processes data from intelligent modules and transmits control actions to the I / O control modules via CAN and RS-485 networks.

- high-performance processor LPC2194 architecture ARM7, with a frequency of 60 MHz Philips;
- the amount of RAM is 16 KB;
- the amount of permanent memory — Flash memory, 256 KB;
- the amount of external non-volatile memory for storing the values of variables — up to 256 KB;
- 3 built-in CAN-controllers;
- The default program cycle time is 1ms when there is no network exchange.
Parameter | Value |
Supply voltage, V | 18 ... 36 (rated voltage 24 V) |
Power consumption, W, not more than | 2,5 |
Electrical insulation resistance of galvanically isolated circuits between themselves and relatively galvanically isolated circuits | At least 40 MΩ at a voltage of 500 V DC |
Number of digital outputs | 22 |
Number of digital inputs | 2 |
Communication interfaces: | |
Galvanically isolated | CAN 2.0B – 3 pc. |
Galvanically isolated | RS-485 – 1 pc. |
No Galvanically isolated | RS-232 – 1 pc. |
Network address | 1 to 15 |
Maximum communication speed on the CAN interface, bps | 1000 К |
Maximum communication speed on the RS-485 interface, bit / s | 115200 |
Communication protocol via CAN interface | CANopen or any other |
Communication protocol via RS-485 interface | Defined programmatically |
Degree of housing protection | IP20 |
Overall dimensions, mm | 100х45х115 |
Weight, kg, no more than | 0,2 |
Installation | To DIN rail |
Average service life, years, not less than | 20 |
Parameter | Value |
Galvanic isolation of digital outputs | By channel |
Switching voltage of output circuits | Up to 36 V DC or AC (amplitude value) current |
Voltage drop on the open output key, V | Not more than 0,9 |
Maximum current of open output key, mA | Not more than 30 |
Leakage current of the closed output key, μA | Not more than 5,0 |
Parameter | Value |
Galvanic isolation of digital inputs | Group |
Maximum channel failure current, mA | 6 |
Minimum operating current of the channel, mA | 10 |
The controller is programmed in C language in the Keil environment. An example of the program using all the features of the controller and a detailed description of the program is on the site. If necessary, according to the relevant terms of reference, it is possible to develop the necessary software.
The controller is programmed via the RS-232 service interface. The programming cable is included in the delivery. There is a special software that allows you to view in real time up to 256 bytes of any memory controller and set the values of program variables.
It is possible to reprogram the CAN (the programming algorithm is given in the programmer’s manual) using a buffer transmission.
Example of using module 740

To connect the termination resistor CAN1, it is necessary to install a jumper between pins 22 and 23.
To connect the termination resistor CAN2, it is necessary to install a jumper between pins 30 and 31.
To connect the termination resistor CAN3, you need to install a jumper between pins 13 and 14.
To connect RS-485, you need to install a jumper between pins 17 and 19.
Connection to the contacts of the module by plugs with spring terminals type FKCT 2,5 / 4-ST from PHOENIX CONTACT (it is allowed to connect single-core and stranded wires with a cross section from 0.2 to 2.5 mm2).
The necessity of completing the module with plugs is specified when ordering.
(URAP.426469.002, URAP.426469.002-01)
The module is intended for use in control and recording systems, digital signal processing systems with high requirements for speed, volume of processed data, reliability and fault tolerance as a computing and control node.

- processor Vortex86DX firm DM & P, clock frequency — 600 MHz;
- external bus 16-bit PC-104, clock frequency — 8/16 MHz;
- The amount of RAM (DDR2 SDRAM) is 256 MB, the clock frequency is 266 MHz;
- the amount of external memory type NAND Flash Disk — 1 GB;
- the amount of external memory type NAND Flash Disk — 1 GB;
- non-volatile timer / calendar;
- power supervisor;
- watchdog timer;
- operating system QNX 6.5.
- MODBUS TCP;
- MODBUS RTU;
- CANopen standard CiA DS301 and any other protocols;
- BACnet/IP.
Parameter | Value |
Supply voltage, V | 18 ... 36 (rated voltage 24 V) |
Power consumption, W, not more than | 12 |
Electrical insulation resistance of galvanically isolated circuits between themselves and relatively galvanically isolated circuits | At least 40 MΩ at a voltage of 500 V DC |
Interfaces: | |
Ethernet 10/100BaseT | 2 pc. |
USB 2.0 | 2 pc. |
No Galvanically isolated | RS-232 – 1 pc. |
Galvanically isolated | RS-485 – 1 pc. |
Galvanically isolated | CAN 2.0 В – 3 pc. |
Degree of housing protection | IP20 |
Overall dimensions, mm | 195х50х130 |
Weight, kg, no more than | 1,4 |
Average service life, years, not less than | 10 |
- to DIN-rail (URAP.426469.002-01);
- screws on the panel or wall (URAP.426469.002)

Connection of external wires to the contacts of connectors X1-X5 is carried out by means of plugs with spring terminals type FKCT 2,5 / 4-ST and FKCT 2,5 / 5-ST from PHOENIX CONTACT (it is allowed to connect single-core and multicore wires with cross-section from 0, 2 to 2.5 mm2). The necessity of completing the module with plugs is specified when ordering.
To program the module, the ISaGRAF 5 development environment is used, using which the user can develop software (software) that meets his requirements. If necessary, according to the relevant terms of reference, it is possible to develop the necessary software.