skip to Main Content
Module 726

(еК2.390.417)

The module is intended for use in control and recording systems, digital signal processing systems with high requirements for speed, volume of processed data, reliability and fault tolerance as a discrete signal input unit.

The module collects data from the discrete inputs of the module and transmits them to the CAN network.

The module works in the CAN network via the CANopen protocol and is always a slave. Therefore, there must be a network master in the CAN network, for example, a PC with a SCADA system running on it, a controller or a controller.

ВВОД ДИСКРЕТНЫХ СИГНАЛОВ модуль 725
Main technical characteristics
ParameterValue
Supply voltage, V18 ... 36
(rated voltage 24 V)
Power consumption, W, not more than2,5
Electrical insulation resistance of galvanically isolated circuits between themselves and relatively galvanically isolated circuitsAt least 40 MΩ at a voltage of 500 V DC
Number of digital outputs12
Communication interfaceCAN 2.0 B
Network address1 to 127
Maximum bit rate on the interface, bps1000 К
Interface communication protocolCANopen
Degree of housing protectionIP20
Overall dimensions, mm100х45х115
Weight, kg, no more than0,2
InstallationTo DIN rail
Average service life, years, not less than20
Parameters of digital outputs
ParameterValue
Galvanic Isolation of Digital OutputsGroup
Maximum channel failure current, mA4
Minimum operating current of the channel, mA7
The delay time for the formation of a discrete signal when the signal at the input changes from "0" to "1" and back, msConfigurable by CAN
from 1 to 65656

Pin 7 – input power module.

Pin 8 – input power supply of the input discrete signals.

Connection to the module contacts by means of plugs with spring terminals type FKCT 2,5 / 4-ST from PHOENIX CONTACT (it is allowed to connect single-core and stranded wires with a cross section from 0.2 to 2.5 mm2). The necessity of completing the module with plugs is specified when ordering.

To connect a CAN termination resistor, a jumper must be installed between pins 13 and 14.

Module 726М

(УРАП.422412.006)

The module is intended for use in control and recording systems, digital signal processing systems with high requirements for speed, volume of processed data, reliability and fault tolerance as a discrete signal input unit.

The module collects data from the digital inputs of the module and transmits them to the RS-485 network.

The module works on the RS-485 network using the ModBus RTU protocol and is always a slave. Therefore, the RS-485 network must have a network master, for example, a PC with a SCADA system running on it, a controller or a controller.

ВВОД ДИСКРЕТНЫХ СИГНАЛОВ модуль 725
Main technical characteristics
NameValue
Supply voltage, V18 ... 36
(rated voltage 24 V)
Power consumption, W, not more than2,5
Electrical insulation resistance of galvanically isolated circuits between themselves and relatively galvanically isolated circuitsAt least 40 MΩ at a voltage of 500 V DC
Number of digital outputs12
Communication interfaceRS-485
Network address1 to 247
Maximum bit rate on the interface, bps38400
Interface communication protocolModBus RTU
Degree of housing protectionIP20
Overall dimensions, mm100х45х115
Weight, kg, no more than0,2
InstallationTo DIN rail
Average service life, years, not less than20
Parameters of digital outputs
ParameterValue
Galvanic Isolation of Digital OutputsGroup
Maximum channel failure current, mA4
Minimum operating current of the channel, mA7
The delay time for the formation of a discrete signal when the signal at the input changes from "0" to "1" and back, msConfigurable by RS-485
from 1 to 65656
""
1
ЗАКАЗАТЬ ОБРАТНЫЙ ЗВОНОК
Ваше Имя
Ваш телефон
Предмет обращенияmore details
0 /
Previous
Next
×
Back To Top
X